What do R, S, C, W, A and M mean on a QintelliM machine?
Direct answer: QintelliM configuration codes describe the processing stations and workpiece-holding arrangement used in a machine. R is an abrasive-belt deburring or grinding station, S is a rotary roller brush edge-rounding station, C is used for dedicated removal of heavy attached thermal-cut slag, and W is a surface-finishing station configured for brushing or polishing according to the selected tooling. A identifies a vacuum holding configuration, M identifies magnetic holding, and A-M combines magnetic and vacuum holding in one project-specific arrangement. Repeated letters indicate repeated stations, while letter order describes the physical process sequence.
Last reviewed: September 17, 2026. This guide describes QintelliM's modular naming logic and is intended to help production engineers compare process configurations.
Watch the R/S/C/W station configuration video
This video shows how QintelliM configures R, S, C and W stations in a metal deburring and surface finishing machine. The R station uses an abrasive belt for deburring or grinding, the S station uses a rotary roller brush for edge rounding, the C station is used for dedicated removal of heavy attached thermal-cut slag, and one W station is configured for brushing or polishing with the selected tooling.
Watch the video on YouTube: QintelliM R/S/C/W station configuration video
What does each station code mean?
| Code |
Station or holding arrangement |
Process role / selection boundary |
| R |
Abrasive-belt deburring / grinding station |
Ordinary burr removal, controlled grinding and related surface preparation where applicable. |
| S |
Rotary roller brush edge-rounding station |
Edge rounding on accessible features; not a fixed-angle chamfer or a guaranteed radius. Confirm the edge result with representative parts. |
| C |
Dedicated heavy-slag removal station |
Removal of heavy attached thermal-cut slag or strongly attached residue, such as suitable plasma- or flame-cut slag, using project-confirmed tooling such as alloy hammers. |
| W |
Surface-finishing station |
Brushing OR polishing according to selected tooling and project requirements. |
| A |
Vacuum holding configuration |
Evaluate effective contact area, flatness, geometry, openings, processing load and actual part stability. |
| M |
Magnetic holding configuration |
Evaluate actual magnetic response, effective contact, geometry, relevant thickness/condition, processing load and application. |
| A-M |
Combined magnetic + vacuum holding arrangement |
Magnetic area, vacuum area, layout and usable area are project-dependent. |
What can one W station do?
A single W station is configured for brushing OR polishing with the selected tooling. QintelliM projects usually prioritize brushing; polishing is evaluated for a specific customer requirement. If separate brushing and polishing steps are needed, evaluate two W stations or another confirmed configuration.
How should a configuration be read?
Read the processing letters from left to right, then read the conveyor suffix. For example, RSW-A describes R abrasive-belt deburring or grinding, followed by S rotary roller brush edge rounding, then one selected W brushing or polishing step, using a vacuum holding arrangement confirmed for the parts. CR-M describes dedicated C heavy-slag removal followed by R abrasive-belt deburring or grinding, with magnetic holding confirmed for the application.
| Example |
Meaning |
Typical goal |
| RR |
Two R abrasive-belt deburring / grinding stations |
Staged burr removal and controlled grinding where the incoming condition requires two R stages. |
| RS |
R abrasive-belt deburring followed by S rotary roller brush edge rounding |
Remove burrs, then create safer rounded edges. |
| RSW |
R abrasive-belt deburring, S edge rounding, then W brushing or polishing |
Complete functional and visual finishing. |
| CR |
Heavy-slag removal followed by deburring |
Process plasma- or flame-cut parts with attached slag. |
| RRSR-A-M |
R-R-S-R processing sequence with a project-specific magnetic + vacuum holding arrangement |
Flexible mixed-material production. |
Decode the physical station sequence
| Code |
Process route |
| RW |
R → W |
| RRS |
R → R → S |
| RSR |
R → S → R |
| RRSW |
R → R → S → W |
| RSRW |
R → S → R → W |
| CRSR |
C → R → S → R |
Installed Configuration vs Active Process Route
A QintelliM configuration code describes the installed physical station sequence of the machine. It does not mean that every installed station must be used for every production batch.
Across QintelliM machine series, every installed processing station can be controlled and used independently. On machines with multiple processing stations, including repeated stations such as RR, any station not required for the current job can be raised and switched off.
The installed configuration remains unchanged even when only part of the available station sequence is active. A switched-off station does not participate in that batch process, but remains part of the installed configuration.
RR
An RR machine has two installed R stations. If a production batch requires only one R operation, one R station can be active while the other R station is raised and switched off. The active process is R, but the machine configuration remains RR.
RS
An RS machine may use only R when edge rounding is not required, with S raised and switched off, or only S when the application requires the S process without using R. In that case, R can be raised and switched off. The machine configuration remains RS.
RSW
An R-S-W machine may use an active R→W route when deburring and brushing are required but edge rounding is not. In that case, S can be raised and switched off while the installed machine configuration remains R-S-W.
The active process route is a subset of the installed stations, used in their original physical order. Independent station control does not change the machine configuration code or rearrange the physical stations. An installed R-S-W sequence can use R→W with S off; independent control cannot turn that physical order into W→R.
See a confirmed aluminum R-S-W production example using an active R→W process.
Learn how RRS and RSR differ when choosing between R-R-S and R-S-R.
A longer or more complex code does not automatically mean better performance. The correct configuration depends on the incoming condition, required edge result, surface requirement, workpiece holding and production target.
To compare complete station sequences, working widths and conveyor options, use the QintelliM metal deburring machine selection guide before selecting an R, S, C or W process combination.
Why do repeated stations matter?
Repeated stations are not simply duplicates. They can divide a difficult process into controlled stages. Two R stations may use different abrasive grades for stock removal and finishing. Additional S stations may distribute edge-rounding work, but any improvement in consistency or throughput must be demonstrated with representative parts and the same inspection method. The correct sequence depends on burr size, material, target finish, part geometry and line speed.
How do A, M and A-M conveyor platforms differ?
- A — vacuum holding: evaluate effective contact area, flatness, geometry, perforations or openings, processing load and actual workpiece stability. A material name or a small/thin part description alone does not establish suitability.
- M — magnetic holding: evaluate actual magnetic response, effective contact, geometry, thickness and condition where relevant, processing load and the application. Do not assume that all steel parts can be held reliably, or that all stainless steel parts are non-magnetic.
- A-M — combined magnetic + vacuum holding: evaluate this arrangement when a project needs to accommodate different workpiece-holding requirements. The magnetic area, vacuum area, layout and usable area are project-dependent; an equal split is not a default specification.
For a detailed holding review, read the Vacuum vs Magnetic Conveyor Guide.
Start from the part condition and required result
Start from the part condition and required result, then read the process code—not the other way around. Evaluate R for ordinary burr removal or controlled grinding, S for a required rounded edge, C for heavy attached thermal-cut slag, and W for a separate surface-finishing requirement. Confirm the final sequence with representative parts.
What information is required before selecting a configuration?
- Material, actual magnetic response and current surface condition.
- Minimum and maximum part dimensions, thickness, flatness, openings and available holding contact.
- Upstream cutting method, such as laser, plasma, flame cutting, punching or machining.
- Burr, oxide or slag condition.
- Required edge radius and surface finish.
- Hourly throughput and automation requirements.
Use this code guide together with the QintelliM deburring machine selection page to compare current R, S, RS, RW and RSW function families, conveyor platforms and working widths.
Use the Sample Testing Guide to prepare representative workpieces and agree the process, holding and result checks before approving a configuration.
Frequently asked questions
Does a longer machine code mean better performance?
No. A longer configuration offers more process stages, but the best solution is the shortest stable process that consistently achieves the required result and throughput.
Can station number and order be customized?
QintelliM can evaluate station quantity, order, working width, holding arrangement and non-standard integration for the project. Feasibility and the final configuration depend on the application, workpiece and verified production requirements.
What is the difference between deburring and edge rounding?
R abrasive-belt deburring removes ordinary burrs and performs controlled grinding. S rotary roller brush edge rounding treats the edge profile; it does not machine a fixed-angle chamfer or guarantee a universal radius. A part may require one or both processes, with the result confirmed through representative sample testing.
Does A or M depend only on material?
No. Material and magnetic response are inputs, but effective contact, geometry, openings, part condition, processing load and observed stability must also be assessed for the selected holding arrangement.
About QintelliM
QintelliM is the brand of Shandong QintelliM Co., Ltd., a manufacturer of modular metal surface finishing and automated deburring equipment. QintelliM equipment configurations are selected from sample testing and application requirements rather than model code alone.
Request a Configuration Review
Send your proposed code, material, workpiece dimensions, burr or slag photos, holding conditions and required edge or surface result. QintelliM can review the process sequence against the application.
Request a Configuration Review